LD Systems IPA412T 4 x 120W 4-Channel Hybrid DSP Amplifier LD Systems

The LD Systems IPA 412 T is a professional, four-channel installation power amplifier with 4 x 120 watts. While the 70V/100V outputs are equipped with high quality toroidal core transformers, the low impedance 4-Ohm outputs are completely transformerless and guarantee the highest possible audio quality. The versatile DSP functions include, amongst others, a parametric EQ with matching speaker library, dynamic tools, a matrix mixer, priority source selection and delay.

Despite this range of functions, the IPA Series power amps are easy to operate. Important functions such as signal, limit, protection and bridge mode are easily visible via the LEDs on the front panel.

HPF/LPF presets can be enabled directly on the device via DIP switches. The IPA 412 T is already equipped for remote control using future remote panels and paging microphones from LD Systems. The back-panel slot provides expansion card connectivity for additional future-proofing. The Ethernet card offers comprehensive configuration and management via software. The Ethernet+Dante card also offers Dante audio networking capabilities and connection to a wide range of Dante-enabled devices, in order to integrate the IPA 412 T into the Dante network and resolve more complex tasks.

Times are changing; rooms are redivided or rededicated, numbers of attendees increase or decrease based on unforeseen events, but with the IPA Series DSP-supported power amps, your installation is prepared for any situation. Scalability and future-proofing are the biggest advantages of the IPA Series. Its energy efficiency is also ideal thanks to the class-D technology and switchable auto standby.

Warranty: 12 Months

Features

• Professional 4-channel installation amplifier
• Powerful class-D power amplifier with 4 x 120 W
• Switchable 4 Ohm (transformer bypass) or 70V/100V outputs through toroidal core transformer
• Stereo/parallel/bridge mode selector switch per channel pair
• 4 balanced line inputs and 4 speaker outputs with terminal block connections
• User-friendly front panel with signal, limit, protection, mute and bridge mode LEDs per channel and clipping LEDs for the inputs
• DSP presets with HPF and LPF which can be activated via DIP switches
• REMOTE audio and control bus based on CAN architecture (Controller Area Network)
• Slot for future optional expansion cards for Ethernet or Ethernet + Dante

Specifications

Product type: Installation power amplifier

Amplifier Type: Class-D

Rated Output: 4 Ohms: 4 x 120 W (1.5 seconds sine burst), 8 Ohms: 4 x 60 W (1,5 Seconds Sine Burst), 16 Ohms: 4 x 30 W (1.5 Seconds Sine Burst), 8 Ohms (bridged): 2 x 235W (1.5 Seconds Sine Burst)

Audio Channels: 4

Output Circuitry: Class D

Operating voltage: Wide Range SMPS with PFC (power factor control)

Mains connector: IEC socket

Auto-Standby Power: Yes. Switchable (On-Off)

Time to Auto-standby: 20 Min with no audio input signal

DSP: Yes

Remote-Bus: Yes

Indicators: Front Panel: “PROT”, “LIMIT”, “SIG”, “BRIDGE” and Mute Symbol LED´s. Power On/ Standby LED , Rear Panel: 4x Input Clip LED´s, Remote Lock LED (Red)

Controls Front panel: On / off switch , standby

Controls Element Back Panel: “BRG“ (Bridge) , “PAR“ (Parallel) , “ST“ (Stereo) , Amplifier Channel Mode , Low-Z and High-Z switches (paired) , Output Volume potentiometers , Preset A and B switches , Remote Lock , Remote ON/OFF , Remote-Mode , Standby On/Off

Inputs: 4x Balanced Line Inputs , Remote Bus Audio Input

Input connectors: 6-pin Terminal Block Pitch 3.81mm , Remote IN/OUT RJ45 , Service Micro USB Type-B

Expansion Slot: For optional Ethernet, or Ethernet + Dante cards

Cooling: front to rear/side airflow , Passive + 2-zone temperature controlled active cooling

Operating voltage: 100 V AC – 240 V AC, 50 – 60 Hz

Fuse: T10AL 250 V

Inrush Current Power: 2.8 A

Power Consumption: Standby: 0.9W, Idle mode: 25W, Full Load: 790W

Operating temperature: 0 °C – 40 °C; (max 60% relative humidity)

Dimensions: 483 x 44.5 x 425 mm

Weight: 8.7kg